You are here: Home arrow Product arrow SKF microlog analyzer arrow SKF Microlog Analyzer GX series CMXA 75-M-K-SL arrow SKF Microlog Analyzer GX series CMXA 75-M-K-SL

Alat Deteksi - Alat Detektor

Info: Your browser does not accept cookies. To put products into your cart and purchase them you need to enable cookies.


SKF Microlog Analyzer GX series CMXA 75-M-K-SL
View Full-Size Image


SKF Microlog Analyzer GX series CMXA 75-M-K-SL



Ask a question about this product

The GX-M [CMXA 75-M-K-SL] standard kit includes:
• CMXA 75-M unit, programmed for two-channel non-route and
route measurements and one or two plane static, or dynamic
couple balancing applications
• Two (2) accelerometers, general purpose, low profile, side exit,
industrial, non-NI, with 1/4-28 and M6 mounting studs
[CMSS 2200]
• Two (2) accelerometer coiled cables, 1,8 m (6 ft.) [CMAC 5209]
• Two (2) medium duty magnetic bases, 35 mm (1.5 in.) diameter
[CMSS 908-MD]
• For additional components available for this kit, see “Kit
Components”
SPECIFICATIONS
Input sources
Acceleration, velocity, and displacement from hand-held or installed
vibration sensors or monitoring systems.
• AC / DC sensors
• Pressure sensors
• Temperature sensors
• Keyboard entry: Measurements read from indicators or installed
instruments entered in engineering units
• Universal tachometer
• Visual inspections: Added to measurement as coded notes
Preprocessing
• Enveloper (demodulator): With four selectable input filters for
enhanced bearing and gear mesh fault detection
• Filter selection:
–– 5 Hz to 100 Hz
–– 50 Hz to 1 kHz
–– 500 Hz to 10 kHz
–– 5 kHz to 40 kHz
• Input parameters:
–– Tachometer: TTL / analogue programmable to 40 V
–– RPM range 1 to 99 999
–– Tachometer power supply output +5 V at 100 mA
• Input over-voltage protection:
–– AC 50 V peak
–– DC 50 V sustained
• Dynamic range: >90 dB (24 bit ADC sigma-delta)
• Input connectors:
–– CH1: Six pin Fischer, CH1, CH2, CH3
–– CH2: Six pin Fischer, CH2, CH3
–– USB host / CHR / headphone: USB keyboard, CHR, headphones
–– USB Device / power / trigger: Seven pin Fischer trigger in,
trigger tachometer power supply, USB COMMS, charger
• Input signal range: 25 V maximum
Data processing and storage
• Microprocessor: Marvell 806 MHz PXA320
• Internal storage: 128 MB (capable of storing approximately 4 000
spectra)
• SD card: SD memory card up to 16 GB
Measurement
• Range:
–– Route measurements: DC to 40 kHz (GX-R: 20 kHz)
–– Non-route measurements: DC to 40 kHz (not available in
GX-R)
• Averaging: 1 to 255 time averages, 1 to 4 096 spectral averages
• Averaging type: RMS, exponential
• Cursor: Fixed and cursor lock. Single, harmonic
and peak pick.
• Trigger modes: Free run or external trigger
(trigger slope and amplitude)
• Resolution: Programmable 100, 200, 400, 800, 1 600, 3 200,
6 400 and 12 800 lines
• Measurement windows: Hanning, flat top and rectangular
• Multi-point automation: Up to 12 measurements can be listed for
one button push automated data collection at each measurement
location
Accuracy
• 0.25% of full scale range
Data displays
• Single and dual channel spectrum, single and dual channel time,
phase table, process, orbit, cross channel phase (GX-R: singlechannel
spectrum, time, phase table, and process)
• Simultaneous spectrum, time waveform, peak hold averaging
• Up to 12 bands (fixed or order base) downloadable from host
software
Power
• Battery: Li-ion smart battery pack
• Eight hours continuous operation minimum
Physical data
• Dedicated keys: Up, down, right, and left two enter keys for right
and left hand operation, four function keys
• Hot keys: Peak find, harmonic, expand
• LCD screen: Color 1/4 VGA 320 ™ 240 pixels
(54 ™ 72 mm) viewable
• Case: High impact ABS with IP 65 dust and splash rating
• Weight: 715 g (1.6 lb.)
• Size (height ™ width):
-Narrowest point:186 X 93 mm (7.4 X 3.7 in.)
-Widest point:186 X 134 mm (7.4 X 5.4 in.)
• Drop test: 2 m (6.6 ft.), to MIL STD 810 specifications
Environmental
• Certifications:
–– Special conditions per certifications
–– ATEX: II 3 G Ex ic IIC T4 Gc (Ta = –10 C to +50 C)
–– IECEx: Ex ic IIC T4 Gc (Ta = –10 C to +50 C)
–– CE rated
–– CSA, Class I, Division 2, Groups A, B, C, D, temperature code
T4@Ta = 50 C
• IP Rating: IP 65
• Temperature ratings:
–– Operating temperature: –10 to +50 C (14 to 122 F)
–– Storage temperature: –20 to +60 C (–4 to +140 F)
• Humidity: 95% non-condensing
Communications
• USB communication
Host software
• The SKF Microlog GX series requires SKF @ptitude Monitoring
Suite, version 4.1.2 or newer software and USB communication